| Caraterísticas | S32eT, S32eJ, S32gT, S32gJ | |
| Conceito do sistema de alarme | Sistema modular hibrido | |
| Zonas com fio na placa | 5/10 (dobrada) | |
| Entrada para detetor de fumo de 2 fios | 1 | |
| Zonas sem fio na placa | 32 | |
| Máximo zonas no sistema | 32 | |
| Saídas PGM na placa | 3 | |
| Máximo PGM no sistema | 16 | |
| Códigos de utilizador + instalador | 31+1 | |
| Código de coação | Yes | |
| Restaurar códigos de utilizador e de serviço | Yes | |
| Zona de comutação de chave | Yes | |
| Partições | 4 | |
| Partição "Compartilhada" (área comum) | Yes | |
| Temporizadores de sistema | 16 | |
| Máximo de teclados / módulos no sistema | 5 | |
| Compatibilidade de teclados | Todos os teclados SECOLINK | |
| Memória do registo de eventos | 256 (no teclado 512) | |
| Interface com transmissores e comunicadores de outros fabricantes | - | |
| Protocolo do bus de dados | KRBUS | |
| Tipo de detector "Estores" (rolo) | Yes | |
| Tipo de detetor "Vibração" | Yes | |
| Velocidade da zona "vibração" (sensibilidade) | 0.01 - 0.25 sec. | |
| Velocidade normal da zona (sensibilidade) | 0.1 - 2.5 sec. | |
| Tipo de laço de zona (detector) | NC, NO, NC/EOL, NO/EOL, NC/DEOL, NO/DEOL, Vibração, Estores, Wireless | |
| Modo de armar | Total, Máximo Total, Noite, Parcial. | |
| Definições de zona | Entrar/sair, entrar/sair forçado, interior, interior armado noite, seguidora, interior seguidora noite, perímetro, instantânea, PGM controlo; 24h: burglary, panic silent, panic audible, tamper, fire, smoke, fire button, medical button, fire supervisory, low water level, RF Jam, gas detected, water leakage, high temperature, low temperature | |
| Atributos de zona | Enable bypass, no alarm, arm when door is closed, entry route, exit route, fire verification, limitation of alarms, limitation of reporting, pre-alarm, armed night | |
| Definições PGM | Fire alarm, fire/burglary alarm, burglary alarm, tamper alarm, technical alarm, selected alarms, chime, zone violation, bypass status, selected trouble, exit/entry warning, exit/arm status, full arm status, power supply, resettable power supply, fire power supply, timer, mono/bi switch | |
| Atributos PGM | Inversion, pulsation, latch, pre-alarm, arm notification, arming failure notification, disarm notification, clear alarm notification, armed in specific mode | |
| Módulo de comunicação incorporado (comunicador), serviços adicionais | ||
| Versões de modem1 |
| |
| Incorporado-SIM (eSIM) | Yes
| |
| SIM de usuário | Sim (tamanho: micro SIM) | |
| Serviços extra que estão incluídos no preço final do produto |
Nota: para activar os serviços extra, é necessário criar uma conta de utilizador na nuvem ALARMSERVER.NET e registar o produto, introduzindo o número de identificação do produto "BI". | |
| Notificações ao utente, envio de relatórios ao CMS usando o cartão SIM do utente ou o eSIM | ||
| SIM do utente | eSIM | |
| Número de destinatários para SMS, mensagens de clipe de voz | 5 | |
| Mensagem de alarme para o utente final por clip de voz | - | |
| Guia de voz para o utente final | - | |
| Saída de SMS (dispositivo >> telefone) | Yes | - |
| SMS in (phone >> device) | Yes | |
| SMS text language (device >> phone) | Can be changed using MASCAD PRO | - |
| Operation of SECOLINK PRO using SMS services: | ||
| Android | texto simples3 | - |
| iPhone | texto simples3 | - |
| Number of recipients for internet messaging using app SECOLINK PRO | 10 | |
| Requirements for online system control using the SECOLINK PRO app |
account in the ALARMSERVER.NET cloud and register the product by entering the product identification number "BI";
for the system4;
with 10 - 20 MB of data per month. |
the final price of the product, the user of the system must create an account in the ALARMSERVER.NET cloud and register the product by entering the product identification number "BI".
|
| Push notifications | Yes5 | Yes |
| Reporting to Central Monitoring Station (CMS) | Yes | Yes (There are additional conditions. Contact CMS company) |
| Reporting to CMS format | CID by GPRS/LTE/LTE Cat-M1 | |
| Reporting protocols for CMS | E2 (Enigma), FIBRO (Sur-gard), CSV (Patriot), SIA | |
| Compatible with SG-SYSTEM II , III IP card | Yes | |
| Maximum load and electrical characteristics | ||
| Rated voltage of power supply (AC) | ~20 V | |
Minimum AC voltage (note: ~16 V input voltage lets control panel to generate max 0,5 A output current) | ~16 V | |
Maximum AC voltage (Note: higher than ~22 V voltage can damage control panel) | ~22 | |
| Requirements for a AC power transformer | ≥30 VA Attention: S32 series control panels are intended for installation in a CAS6 plastic casing. These control panels cannot be installed in the CAS4 plastic casing due to the low power AC transformer used in it. | |
| Maximum long term output current of control panel (I+AUX + I+BELL + IBattery charge) | ≤1 A | |
| Maximum current of slow blowing fuse used in primary AC | 250 mA | |
| Maximum AC power consumption | 150 mA | |
| Minimum voltage on +AUX, +BELL outputs | 12 V | |
| Maximum voltage on +AUX, +BELL outputs | 13,9 V | |
| Maximum current out of +AUX | +0,8 A | |
| Maximum current out of +BELL | +2 A | |
| Maximum current into -PGM1 | -0,15 A | |
| Maximum current into -PGM2 | -0,15 A | |
| Short circuit, overload protection of +BELL, +AUX | Electronic | |
| Battery charge, +BELL, +AUX current measurement | Yes | |
| Failed (waste) backup battery disconnection | Yes | |
| Maximum battery charging current | +0,2 A | |
| Maximum current of fast blowing fuse used in battery circuit | 3,15 A | |
| Control panel disconnect battery when it’s voltage less than | 9,5 V | |
| Operational compliance | EN50131, Grade2 | |
| Recommended backup battery | 12 V, 2,2 - 7Ah | |
| Overall dimensions W x H in mm | 145 x 77 | |
| Environmental compliance | ROHS | |
| Operating temperature | From -10oC up to +50oC | |
| Remote programming of control panel settings | Yes | |
| Production status | In production | |
| Interface with PC | USB micro-B | |
| Latest firmware version |  Download | |
| Wiring manual |  Download | |
| Programming manual (for keypad KM20Bx) | Download | |
| Programming manual (for keypad KM24x, KM25) | Download | |
1 - GSM providers are planning to start 2G network shutdown in 2026-2028, so it is worth thinking about the future now. The control panels use communication modems that support both the current, but aging, 2G technology, as well as LTE and LTE Cat-M1 technologies, which will replace it in the future. | ||
2 - at the end of the paid period, the user will be offered to renew the license. The license is renewed upon purchase of a GSIM voucher. If the license is not renewed the control panel will only be usable to report to the CMS receiver. The user has an option to insert his SIM card and continue to use control panel (additional programming of control panel will be required). Before purchasing a control panel, it is necessary to check whether the price of the extension (GSIM voucher) is acceptable. You can buy the voucher at https://shop.secolink.eu | ||
3 - SMS messages from the control panel are not imported into the SECOLINK PRO app - they can be viewed using the SMS editing app on the phone. Lock icons (ARMED / DISARMED) are not displayed in the app. SMS commands are not performed in the background - SECOLINK PRO will „insert“ the control command for the user into SMS editing app and the user will need to tap on the button Send. | ||
4 - WLCT voucher can be purchased at https://shop.secolink.eu | ||
5 - ALARMSERVER.NET cloud services should be in use. WLCT voucher can be purchased at https://shop.secolink.eu | ||