fbpx
Caraterísticas S32emR, S32gmR S32em, S32gm
Conceito do sistema de alarme Sistema modular hibrido
Zonas com fio na placa 5/10 (dobrada)
Entrada para detetor de fumo de 2 fios 1
Zonas sem fio na placa - 32
Máximo zonas no sistema 32
Saídas PGM na placa 3
Máximo PGM no sistema 16
Códigos de utilizador + instalador 31+1
Código de coação Yes
Restaurar códigos de utilizador e de serviço Yes
Zona de comutação de chave Yes
Partições 4
Partição "Compartilhada" (área comum) Yes
Temporizadores de sistema 16
Máximo de teclados / módulos no sistema 5
Compatibilidade de teclados Todos os teclados SECOLINK
Memória do registo de eventos 256 (no teclado 512)
Interface com transmissores e comunicadores de outros fabricantes -
Protocolo do bus de dados KRBUS 
Tipo de detector "Estores" (rolo)
 Yes
Tipo de detetor "Vibração" Yes
Velocidade da zona "vibração" (sensibilidade) 0.01 - 0.25 seg.
Velocidade normal da zona (sensibilidade) 0.1 - 2.5 seg.
Tipo de laço de zona (detector) NC, NO, NC/EOL, NO/EOL, NC/DEOL, NO/DEOL, Vibração, Estores, Wireless
Modo de armar Total, Máximo Total, Noite, Parcial.
Definições de zona

Entrar/sair, entrar/sair forçado, interior, interior armado noite, seguidora, interior seguidora noite, perímetro, instantânea, PGM controlo;

24h: burglary, panic silent, panic audible, tamper, fire, smoke, fire button, medical button, fire supervisory, low water level, RF Jam, gas detected, water leakage, high temperature, low temperature
Atributos de zona Enable bypass, no alarm, arm when door is closed, entry route, exit route, fire verification, limitation of alarms, limitation of reporting, pre-alarm, armed night
Definições PGM Fire alarm, fire/burglary alarm, burglary alarm, tamper alarm, technical alarm, selected alarms, chime, zone violation, bypass status, selected trouble, exit/entry warning, exit/arm status, full arm status, power supply, resettable power supply, fire power supply, timer, mono/bi switch
Atributos PGM Inversion, pulsation, latch, pre-alarm, arm notification, arming failure notification, disarm notification, clear alarm notification, armed in specific mode
Módulo de comunicação incorporado (comunicador), serviços adicionais
Versões de modem1
  • S32emR, S32em - para rede 2G e rede LTE Sub-rede Cat-M1
  • S32gmR, S32gm - para redes 2G e LTE
Incorporado-SIM (eSIM) No
SIM de usuário Sim (tamanho: micro SIM)
Serviços extra que estão incluídos no preço final do produto
  • o painéi de controlo são fornecidos com pagos 6 meses de serviços de nuvem, permitindo ao utilizador tirar o benefícios da aplicação SECOLINK Pro2.

Nota: para activar os serviços extra, é necessário criar uma conta de utilizador na nuvem ALARMSERVER.NET e registar o produto, introduzindo o número de identificação do produto "BI".
Notificações para o usuário, informando o CMS usando o cartão SIM do usuário
Número de destinatários para SMS, mensagens de clipe de voz  5
Mensagem de alarme para o utente final por clip de voz Sim (apenas S32gmR, S32gm)
Guia de voz para o utente final Sim (apenas S32gmR, S32gm)
Saída de SMS (dispositivo >> telefone) Yes
SMS in (phone >> device) Yes
SMS text language (device >> phone) Can be changed using MASCAD PRO
Operation of SECOLINK PRO using SMS services:  
    Android texto simples3
    iPhone texto simples3
Number of recipients for internet messaging using app SECOLINK PRO  10
Requirements for online system control using the SECOLINK PRO app
  • the system user must create an account in the ALARMSERVER.NET cloud and register

     the product by entering the product identification number "BI";

  • the online service must be activated for the system4;
  • the system requires a user SIM card with 10 - 20 MB of data per month.
Push notifications Yes5
Reporting to Central Monitoring Station (CMS) Yes
Reporting to CMS format CID by GPRS/LTE/LTE Cat-M1
Reporting protocols for CMS E2 (Enigma), FIBRO (Sur-gard), CSV (Patriot), SIA
Compatible with SG-SYSTEM II , III IP card Yes
Maximum load and electrical characteristics
Rated voltage of power supply (AC) ~20 V

Minimum AC voltage

(note: ~16 V input voltage lets control panel to generate max 0,5 A output current)

 ~16 V 

Maximum AC voltage

(Note: higher than ~22 V voltage can damage control panel)

 ~22

Requirements for a AC power transformer

≥30 VA

Attention: S32 series control panels are intended for installation in a CAS6 plastic casing. These control panels cannot be installed in the CAS4 plastic casing due to the low power AC transformer used in it.
Maximum long term output current of control panel (I+AUX + I+BELL + IBattery charge)  ≤1 A
Maximum current of slow blowing fuse used in primary AC 250 mA 
Maximum AC power consumption 150 mA
Minimum voltage on +AUX, +BELL outputs 12 V 
Maximum voltage on +AUX, +BELL outputs 13,9 V 
Maximum current out of +AUX +0,8 A
Maximum current out of +BELL +2 A
Maximum current into -PGM1 -0,15 A
Maximum current into -PGM2 -0,15 A
Short circuit, overload protection of +BELL, +AUX Electronic
Battery charge, +BELL, +AUX current measurement Yes
Failed (waste) backup battery disconnection Yes
Maximum battery charging current +0,2 A
Maximum current of fast blowing fuse used in battery circuit 3,15 A
Control panel disconnect battery when it’s voltage less than 9,5 V
Operational compliance EN50131, Grade2 
Recommended backup battery 12 V, 2,2 - 7Ah
Overall dimensions W x H in mm 145 x 77
Environmental compliance ROHS 
Operating temperature From -10oC up to +50oC 
Remote programming of control panel settings Yes
Production status In production In production
Interface with PC USB micro-B 
Latest firmware version Download
Wiring manual  Download
Programming manual (for keypad KM20Bx)  Download
Programming manual (for keypads KM24x, KM25)  Download

   1 - GSM providers are planning to start 2G network shutdown in 2026-2028, so it is worth thinking about the future now. The control panels use

communication modems that support both the current, but aging, 2G technology, as well as LTE and LTE Cat-M1 technologies, which will replace it in the future.

   2 - at the end of 6 months of a paid period, the user will be offered to renew the license. The license is renewed upon purchase of a WLCT voucher. The

control of the control panel over internet will be disabled if the license will not be renewed. The user will still be able to control the control panel with SMS. You can buy the voucher at https://shop.secolink.eu

   3 - SMS messages from the control panel are not imported into the SECOLINK PRO app - they can be viewed using the SMS editing app on the phone. Lock

icons (ARMED / DISARMED) are not displayed in the app. SMS commands are not performed in the background - SECOLINK PRO will „insert“ the control command for the user into SMS editing app and the user will need to tap on the button Send.

   4 - WLCT voucher can be purchased at https://shop.secolink.eu

   5 - ALARMSERVER.NET cloud services should be in use. WLCT voucher can be purchased at https://shop.secolink.eu